How to Polish Stained Glass Solder

how-to-polish-stained-glass-solder-image-4

If you have ever wondered how to polish stained glass solder, you are not alone. Stained glass is an expensive craft to learn, and there are many different steps to take when trying to polish your work. The first step to a beautiful piece of work is removing the oxidation built up over time, which can be accomplished using a product such as 91% alcohol and cotton balls. You want to avoid micro-scratches when cleaning. You can then use a product like a carnauba wax to seal the copper patina in place.

Cleaning with 91% alcohol and cotton balls

If you have recently put a lick of solder on your wares, you are likely wondering how to clean your work of art. Luckily, a few tricks are up your sleeve to keep your pieces looking like the day you got them. The first tip is to leave them in their box for at least a week. While sitting, you can polish them out with abrasive elements.

A microfiber cloth is a good bet. You want something that isn’t too wet to sift out the patina. You can also use the same material to pick up the blackish waste from the soldered part of your bauble. This is especially useful if you plan to buff the heck out of it. You’ll want to do this with a hair dryer as well.

Another tip is to get a good hold of a good-quality duster. Not only will it clear up any loose dust, but it will help you see all the little nooks and crannies you missed during the cleaning process.

While you are at it, make sure to test your mettle with a few different types of cleaners. Never use ammonia-based cleaners, as they can be harsh on your wares. They may be able to get rid of the tarnish in the process, but they will also leave a residue in the form of rust. In addition, you can always take the snafu above one step further by using distilled water and dish soap solution to clean the whole shebang.

How to Polish Stained Glass Solder image 3

You’ve probably seen this adage, but you have yet to hear it from a pro. Having a striking piece of stained glass in your home is nice, but keeping it in top condition is just as important. To this end, you’ll need to keep it in the darkroom for at least a few days to a week. You can also apply a suitable varnish or lacquer coating to prevent the glass from chipping.

Avoiding micro-scratches

The best way to avoid micro-scratches is to use a little common sense. For example, don’t let the last guy touch your glass, or you could get a streak. One of the biggest mistakes is not following the glass maker’s guide to soldering. This can be an expensive mistake. A good rule of thumb is to place the glass on a level surface, such as a worktable or even the floor, to reduce the risk of a slip. Many people think of this as something other than a time-saving measure, but it can be the difference between a successful project and a disastrous one.

A small amount of glass polishing compounds, such as tin flakes or a squirt bottle, can eliminate many of these mishaps. The best part is you can pick up a few new tricks at a fraction of the cost of hiring a professional. Besides, what are you supposed to do if you can’t get the job right the first time? You’ve spent a few hundred dollars for the same service elsewhere. Taking time to learn the nitty-gritty can pay off big in the end. To get the most from your investment, ask a few questions and ensure the best product at the best price.

Getting a copper patina

Getting a copper patina when polishing stained glass solder requires some preparation. First, the solder must be free from oxidation. Then, you will need to clean it thoroughly. You can use a non-ammonium cleaner. A good cleanser is Kwik-Cleaner.

You will also need a chemical brush. Some companies, such as Novacan, manufacture specialized chemical brushes for patina. You can buy these in an 8-ounce bottle.

How to Polish Stained Glass Solder image 2

Once you have cleaned and polished the stained glass, you can apply patina. Several types of patina are available, including black, green, and brown. You can use these on stained glass with a Q-tip or a chemical brush. However, it would help if you were careful not to contaminate the glass with the patina.

Adding sulphuric acid to your homemade patina can improve its effectiveness. It is also a good idea to apply a clear coat of wax to seal the patina. This will help protect the patina and prevent corrosion.

Another way to achieve a patina on your solder is to use the Novacan Copper Patina. This premixed solution can be applied to the glass with a clean chemical brush. The copper patina will gradually darken as it dries and will return to its original brightness with polishing.

You will want to ensure the patina is dry before storing it. It would help if you kept it for less than a week or two. You can remove any patina already on the stained glass with a cotton ball or paper towel. It should not be rinsed with water, as tap water can stain the copper finish.

If the patina gets into the bloodstream, it can damage the liver. If you have any questions, you should speak to your doctor.

How to Polish Stained Glass Solder image 1

It would help if you applied patina to solder for a week. If you have white crud build-up on the solder, you can clean it with an ammonia solution. It would help if you dried the solder with a paper towel.

Finishing with carnauba wax

When a stained glass piece is oxidized, the surface becomes dull. This can be prevented by polishing the glass with a finishing compound. This is similar to waxing a car. It helps prevent the patina from dulling and adds a protective finish. There are several different types of finishing compounds. You can use them on both glass and metal. The more expensive ones can make the black patina look shiny, and the cheaper ones can help keep the copper patina looking bright.

Stained glass solder must be cleaned thoroughly before it can be polished with a finishing compound. Using a cleaning product containing 91% isopropyl alcohol will neutralize the white crud build-up on the surface of the solder. A clean cloth or paper towel should apply the finishing compound. It should be used in a light rubbing motion and kept on the glass for a short time.

After applying the finishing compound, allow it to dry. If you do not have a soft cloth, use a microfiber or old t-shirt to apply it. A final buff-up should be done periodically. A soft cloth should be used for rubbing the finishing compound. If a streak or two occurs, you can use a second towel in a light patting motion.

Before storing the stained glass, it should be stored in a cool, dark place. If it is not stored correctly, the solder may rust. It is also important not to keep the stained glass for more than one week.

How to Polish Stained Glass Solder image 0

Aside from polishing, a patina can also turn silver-colored solder lines into copper. The patina should be applied to the solder within one or two weeks after the solder is finished. You can use a Q-tip to apply the patina or a wax. If you choose to use wax, it should be removed after two days.

Finally, a tarnished or dull finish can be restored with a heavy coat of carnauba wax. This will bring the solder to its former luster and give it a bright, penny-copper look.

Like this post? Please share to your friends:
Leave a Reply

;-) :| :x :twisted: :smile: :shock: :sad: :roll: :razz: :oops: :o :mrgreen: :lol: :idea: :grin: :evil: :cry: :cool: :arrow: :???: :?: :!: